PIN8000/PIN8010 Pneumatic HI Source Pressure Intensifier

  • Available in self-contained enclosure with carrying handles (PIN8000) or 19-inch wide, rack-mount version (PIN8010)
  • Internal precision pressure intensifier generates up to 10 times input pressure
  • Electronically controlled intensifier system
  • Two output (test) ports, for connecting to Device-Under-Test as well as a precision calibration standard (works with all major brand pressure calibrators, digital gauges or indicators)
  • Precision Condec REG1000 (regulator) to adjust input pressure
  • Three gauges to monitor regulated pressure, accumulated pressure, and output pressure
  • Patented micro-metering valves with vernier for precision (.0005 psi) for pressure adjustment and venting
  • Quick-disconnect fittings and hoses supplied for input and output pressure
  • Easy to operate, training can be accomplished in 10 minutes
  • Different technicians can operate the system and get identical results
  • Pneumatic only; no hydraulics or distilled water messes
Cotizar por whatsapp


Although, similar in design to the PIN7000, the PIN8000 features two output ports and our patented Orion 3A valve, with vernier for finger-tip adjustments. Do calibrations utilizing the PIN8000 or PIN8010 pneumatic pressure intensifier. Both the PIN8000 and PIN8010 (19-inch rack-mount) operate using any clean dry air or gaseous nitrogen.

Containing an automatic precision intensifying system, these models generate up to 10 times the input pressure. This easy-to-operate system provides fingertip control within the exclusive patented precision Orion 3A valve. By utilizing the soft-seal micro-metering valves for pressure adjustment and venting, in conjunction with the vernier, user gains finite control to obtain exact pressure readings.

By properly setting the included Condec REG 1000 regulator, units under test are protected from permanent damage due to overpressure. PIN8000 eliminates the inconvenience and physical stress of hand pumps. It has two output (test) ports for connecting to a measuring device and virtually any electronic calibrator. For added convenience, the removable cover allows PIN8000 to be positioned at different angles for easy operation in tight spaces.


  • High pressure supply, up to 10,000 psi, for test equipment
  • Ideal for fluid-free high pressure calibration
  • Works with all major manufacturer’s electronic pressure calibrators



Condec PIN8000/PIN8010 Specifications


Temperature range:
Operating: 40°F to 140°F (4°C to 60°C)
Storage: 0°F to 185°F (-17°C to 85°C)
Relative humidity: 95%, non-condensing

Pressure Media:
Clean dry gaseous nitrogen or clean dry air

Regulated Pressure Gauge:
Size: Two and one half-inch diameter
Range: 0-1500 psi

Accumulator and Output Pressure Gauges:
Size: Two and one half-inch diameter
Range: 0-15,000 psi

Control valves:
Type: Micro-metering with positive shut off, adjustable stop and replaceable seat, non destructible
Vernier mechanical rotation: 16 turns, nominal
Adjustable sensitivity: 0.0005 psi, minimum
Vernier torque: Finger tip adjust to 10,000 psi
Material: 300 series stainless steel outer body

Internal piping:
Tubing: 1/4 in. O.D. and 1/8 in. O.D. 300 series stainless steel, seamless
Couplings: 300 series stainless steel Swagelok®

Output test ports:
Style: Quick-disconnect type
Pressure rating: 10,000 psig minimum, connected or disconnected
Quantity supplied: 2 output Quick Disconnects (one, p/o output pressure hose mentioned below)

Pressure Hoses:
Quantity supplied: 2; one input and one output
Length: 4 ft., nominal each hose
Booster Pump solenoid valve:
Type: Three-way, normally closed, electronically controlled
Pressure rating: 1500 psig
Power Requirements:
115 VAC, 50 Hz, 10 watts
Note: 220 VAC also available

Input Pressure Condec REG 1000 Regulator:
Pressure rating: 3000 psi maximum
Output pressure range: 0-1000 psi
Construction: Self-relieving, single stage regulator

External housing:
PIN8000: Deep drawn aluminum case with cover and handles
PIN8010: Sheet aluminum enclosure

External Finish:
PIN8000: Grey polyurethane baked-enamel paint, textured finish
PIN8010: Dark Tan polyurethane baked-enamel paint, textured finish

Approximately 40 lb (18.1 kg), nominal including all fitting, hoses and power cord