PIN7000/PIN7010 Pneumatic Pressure Intensifier

  • Internal precision pressure intensifier generates up to 10 times input pressure
  • Electronically controlled intensifier system
  • Precision regulator to adjust input pressure
  • Three gauges to monitor regulated pressure, accumulated pressure, and output pressure
  • Patented micro-metering valves for pressure adjustment and venting
  • Quick-disconnect fittings and hoses supplied for input and output pressure
  • Easy to operate, training can be accomplished in 10 minutes
  • Available in self-contained enclosure with carrying handles (PIN7000) or 19-inch, rack-mount version (PIN7010)
Cotizar por whatsapp


Pump up your system with the PIN7000 or PIN7010 pneumatic pressure intensifier. Both the PIN7000 and PIN7010 operate using any clean dry air or gaseous nitrogen. Containing an automatic precision intensifying system, these models generate up to 10 times the input pressure.

This easy-to-operate system provides fingertip control with the exclusive micro-metering valve for pressure adjustment and venting. Monitoring has never been easier with three gauges that account for regulated pressure, accumulated pressure and output pressure. These units are completely equipped with quick-disconnect fittings and hoses for rapid input and output pressure.

These pressure intensifying systems were designed for custom use. The compact PIN7000 incorporates a portable configuration for on-the-go operation. The rugged PIN7010 is a rack-mount model, ideal for frequent in-house use.


  • High pressure supply, up to 10,000 psi, for test equipment
  • Ideal for fluid-free high pressure calibration
  • Works with all major manufacturer’s electronic pressure calibrators


Condec PIN7000/PIN7010 Specifications

Temperature range:
Operating: 40°F to 140°F (4°C to 60°C)
Storage: 0°F to 185°F (-17°C to 85°C)
Relative humidity: 95%, non-condensing

Pressure Media:
Clean dry gaseous nitrogen or clean dry air

Regulated Pressure Gauge:
Size: Two and one half-inch diameter
Range: 0-1500 psi

Accumulator and Output Pressure Gauges:
Size: Two and one half-inch diameter
Range: 0-15,000 psi

Control valves:
Type: Micro-metering with positive shut off, adjustable stop and replaceable seat, non destructible
Vernier mechanical rotation: 16 turns, nominal
Adjustable sensitivity: 0.0005 psi, minimum
Vernier torque: Finger tip adjust to 10,000 psi
Material: 300 series stainless steel outer body

Internal piping:
Tubing: 1/4 in. O.D. and 1/8 in. O.D. 300 series stainless steel, seamless
Couplings: 300 series stainless steel Swagelok®

Output test ports:
Style: Quick-disconnect type
Pressure rating: 10,000 psig minimum, connected or disconnected
Quantity supplied: 2 output Quick Disconnects (one, p/o output pressure hose mentioned below)

Pressure Hoses:
Quantity supplied: 2; one input and one output
Length: 4 ft., nominal each hose
Booster Pump solenoid valve:
Type: Three-way, normally closed, electronically controlled
Pressure rating: 1500 psig
Power Requirements:
115 VAC, 50 Hz, 10 watts
Note: 220 VAC also available

Input Pressure Condec REG 1000 Regulator:
Pressure rating: 3000 psi maximum
Output pressure range: 0-1000 psi
Construction: Self-relieving, single stage regulator

External housing:
PIN7000: Deep drawn aluminum case with cover and handles
PIN7010: Sheet aluminum enclosure

External Finish:
PIN7000: Grey polyurethane baked-enamel paint, textured finish
PIN7010: Dark Tan polyurethane baked-enamel paint, textured finish

Approximately 40 lb (18.1 kg), nominal including all fitting, hoses and power cord